Picture 1 of 9
![Picture 1 of 9](https://i.ebayimg.com/thumbs/images/g/HusAAOSwOCtmWxOq/s-l500.jpg)
![Picture 2 of 9](https://i.ebayimg.com/images/g/tkQAAOSw-EFmWxOs/s-l64.jpg)
![Picture 3 of 9](https://i.ebayimg.com/images/g/sk8AAOSwOmxmWxOu/s-l64.jpg)
![Picture 4 of 9](https://i.ebayimg.com/images/g/mpQAAOSwkFtmWxOv/s-l64.jpg)
![Picture 5 of 9](https://i.ebayimg.com/images/g/Xl0AAOSwwsNmWxOw/s-l64.jpg)
![Picture 6 of 9](https://i.ebayimg.com/images/g/URQAAOSwF79mWxOx/s-l64.jpg)
![Picture 7 of 9](https://i.ebayimg.com/images/g/EQwAAOSwPJNmWxOz/s-l64.jpg)
![Picture 8 of 9](https://i.ebayimg.com/images/g/waMAAOSwvfRmWxO1/s-l64.jpg)
![Picture 9 of 9](https://i.ebayimg.com/images/g/7YwAAOSwk2pmWxO2/s-l64.jpg)
Picture 1 of 9
![Picture 1 of 9](https://i.ebayimg.com/images/g/HusAAOSwOCtmWxOq/s-l1600.jpg)
![Picture 2 of 9](https://i.ebayimg.com/images/g/tkQAAOSw-EFmWxOs/s-l1600.jpg)
![Picture 3 of 9](https://i.ebayimg.com/images/g/sk8AAOSwOmxmWxOu/s-l1600.jpg)
![Picture 4 of 9](https://i.ebayimg.com/images/g/mpQAAOSwkFtmWxOv/s-l1600.jpg)
![Picture 5 of 9](https://i.ebayimg.com/images/g/Xl0AAOSwwsNmWxOw/s-l1600.jpg)
![Picture 6 of 9](https://i.ebayimg.com/images/g/URQAAOSwF79mWxOx/s-l1600.jpg)
![Picture 7 of 9](https://i.ebayimg.com/images/g/EQwAAOSwPJNmWxOz/s-l1600.jpg)
![Picture 8 of 9](https://i.ebayimg.com/images/g/waMAAOSwvfRmWxO1/s-l1600.jpg)
![Picture 9 of 9](https://i.ebayimg.com/images/g/7YwAAOSwk2pmWxO2/s-l1600.jpg)
Better than the original OEM part. The factory pin had little to no means to grease. This pin has a grease groove top and bottom and the center hole goes all the way through. Now I can grease both bushing from the top of the pin. The pin is hardened and when I installed the new bushings, it required I remove about .003" from the pin OD to make it fit (I did not have a reamer). Carbide tooling did the job. The only thing I would suggest is that the supplier of this new pin include a grease zerk that fits. The thread pattern of the hole in the pin is a 3/8-24 and I had to run a die over a standard zerk to make it fit.
Verified purchase: Yes | Condition: New
Fit very nice. Anyone wondering. The newer 10 series uses the same pin and one of these bushings. . The lower bushing is cut down to 1" and fit perfect.
Verified purchase: Yes | Condition: New
Great value good quality
Verified purchase: Yes | Condition: New
well worth the price and it fit perfect
Verified purchase: Yes | Condition: New
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Best Selling in Steering & Power Steering
Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Save on Steering & Power Steering