5stars
14ratings4stars
3ratings3stars
2ratings2stars
0rating1star
0rating
Would recommend95% agree
Good value95% agree
Good quality100% agree
18 Reviews
Although I have just started testing it with a watercooler recirculating machine, so far it's been working beautifully, certainly pulls more than I th
Although I have just started testing it with a watercooler recirculating machine, so far it's been working beautifully, certainly pulls more than I thought it would. One thing to be aware of is that it has no lifting capacity on the suction side, it must be submerged at the bottom and is able to pump water as I got through about 10 feet of distance on the output side with about 2 foot rise.Read full review...
Verified purchase: Yes | Condition: new | Sold by: coldandcolder
Need more info/ startup wattage. Not like a brushed motor.
Did not work for my solar panel application. Although it is stated 0.5-4 Watts, it uses much more power on startup. My 7 watt solar panel (verified/tested power) was unable to start the motor. A 9-volt battery starts and runs it easily and the pump runs great but it is useless for my application.Read full review...
Verified purchase: Yes | Condition: new | Sold by: coldandcolder
Pumped About This Pump
I use it to circulate water for liquid cooling, and it works flawlessly with a 6v, 350ma dc transformer. It pumps water about two feet on a vertical slant (maybe 65°?) and has also had more particulate than one should reasonably run though a pump, and never misses a beat. Regarding the negative aspects, I haven't found any yet, and would not only order this again but would recommend it to anyone else looking for something similar.Read full review...
Verified purchase: Yes | Condition: new | Sold by: coldandcolder
Works well for PC water cooling.
This is a great and quiet water pump!
I'm using this in a PC as a water cooling pump in a custom loop. the loop includes a big 360mmX60mm reservoir, a high density CPU block, and a 46mm thick 360MM radiator. the flow is good for allowing the fluid to be in the radiator long enough to really dissipate heat.
I recommend this.
only downside I can think of is that, hooking up the tubing to it was a challenge but not nearly impossible.
the way I attached my tubing to it was like this: directly connected to this pump is a 1/4in ID tubing which goes to adapters from my local hardware store, to fit into my 3/8in ID tubing.Read full review...
Verified purchase: Yes | Condition: new | Sold by: coldandcolder
So far, so good...
Sorry that I have not had a chance to do much testing of the product so far, but it is at least what I would expect at this time. As I keep testing the product, it may exceed expectations, but haven't gotten that far as of yet.Read full review...
Verified purchase: Yes | Condition: new | Sold by: coldandcolder
Quiet, inexpensive and waterproof
Quiet, inexpensive and waterproof
Verified purchase: Yes | Condition: new | Sold by: coldandcolder
Quiet and quality motor
Quiet and powerful, made a great replacement for a motor that has gone bad
Verified purchase: Yes | Condition: new | Sold by: coldandcolder
Lapidary Pump
I'm using this as an external pump for a small lapidary setup. So far it works great. I did have to put some Teflon tape on the pump head threads as there was no rubber seal to stop a small drip. So far it pumps dirty water just fine.
Note: the pump is not a self priming pump so it needs to sit below the level of water contained in the tank.Read full review...
Verified purchase: Yes | Condition: new | Sold by: coldandcolder
Small and work great!
Solid material made.
Verified purchase: Yes | Condition: new | Sold by: coldandcolder
Great but
Good quality
Verified purchase: Yes | Condition: new | Sold by: coldandcolder